Always discharge the anode of the tube. After servicing make the following leakage current. Unplug the a. Measure the resistance value with an ohmmeter,. When the exposed metallic part has a return path to the chassis, the reading should be between 4M ohm and 20M ohm.
When the exposed metal does not have a return path to the chassis, the reading must be infinite. Plug the a. Do not. Use an a. Check each exposed metallic part and check the. Reverse the a. The potential at any point should not exceed. In case a measurement is outside the limits specified, there is a possibility of a shock hazard, and the receiver should be repaired and rechecked before it is returned to the customer.
Stations are sorted into the following order:. S DVB Stations: Are sorted by their logical channel number sent by the broadcasters, which can be grouped into a favourite channels list by using Profile Edit.
See page S Analogue Stations: Are sorted into channel order, but can be changed to your preference. The sorted programme order depends upon the TV signal, the broadcasting system, and reception conditions. Only the analogue programme positions will be downloaded to the recording device, in the same order as stored in the TV. If a recording device other than those described above has been connected, then there will be no download operation.
Ask your dealer for further details. D For further information on QLink and connecting equipment, see pages 39 and If not, using the left or right cursor buttons move to the NAME line. Change character using the up or down cursor buttons. You are now ready to begin viewing programmes The cursor controls provide the two basic functions:. Access to channels can also be gained using the guide button.
See pages 11 and The DVB TV Guide displays the current programmes being transmitted, and forthcoming programmes on each DVB channel, up to about one week ahead If broadcasters transmit the programmes information. Press the Red button to move the EPG listing to the previous day. Press the Green button to move the EPG listing to next day. Press the Yellow button to view a list of Categories. You can create a favourites list can be customised using the Profile Edit menu see page Press the OK button to view a list of the selected category.
To view any of the current DVB programmes, select it with the cursor buttons and press the OK button. Select the programme for which you require further information using the cursor buttons. Press the i button again to return to the list of programmes. When you select a future programme from the EPG listing, press the OK button to set timer programming for recording on a QLink compatible recorder.
Information banner will appear when changing channel, or pressing the Information button. The banner gives the user information about the channel and programme currently being viewed.
The banner will time out and dissapear from the screen after a set time period, this time period can be set in the DVB System Setup menu. Press the left or right cursor button while banner is displayed to switch between Now and Next. This switches between the information for the current Programme being shown Now and the next Programme to be shown Next.
Press the up or down cursor button to step through the banner information for all channels. Press the OK button to view a channel. Now and Next can also be used in this mode. Press the i button to display an extended banner showing any information available on the current selected programme. Press the i button while in extended banner mode to return to normal banner view. To clear the banner from the screen while in extended banner mode, press the EXIT button.
Press the Blue button while in the banner to scroll through available categories. Pressing the i Information button will display the analogue channel information for a few seconds. This will then be timed out to display just the programme position number near the top left corner of the screen.
To remove this programme position number, press the i Information button again. Auto Aspect determines the best aspect ratio to use to fill your screen. It does this using a four step process to determine if the picture being viewed is a widescreen picture. If Auto Aspect does not. The text shown on the screen indicates how Auto Aspect determined which ratio to use:. Auto Aspect switches to the appropriate or widescreen ratio. Auto Aspect chooses the best ratio and expands the picture to fill the screen.
This process can take several minutes, depending on the darkness of the picture. You may prefer to manually select one of the other aspect options available to view the picture. D If, in Auto Aspect mode, you experience problems with the screen display size when playing back widescreen format recordings from your VCR then it is possible that the tracking control of your VCR requires adjustment your VCR instruction book will contain adjustment details.
D The widescreen aspect ratios of different films and programmes can vary. If these are wider than a standard aspect picture then a black band may be visible at the top and bottom of the screen.
Zoom1 will display letterbox or pictures with no aspect distortions. Zoom2 will display anamorphic letterbox pictures as a full screen display with no aspect distortions. Zoom3 will display letterbox pictures as a full screen display with no aspect distortions. Some selections, for example, Contrast, Brightness, Colour and Sharpness will allow you to increase or decrease their level.
Some selections, for example, Off timer , allow a choice to be made. Some selections, for example Tuning menu , will lead to a further menu. The MENU button is used to open the main menu and also to return to the previous menu.
The up and down cursor buttons are used to move the cursor up and down the menus. The left and right cursor buttons are used to access menus, adjust levels or to select from a range of options. The EXIT button is used to exit the menu system and return to the normal viewing screen. Certain functions have a last position memory, i. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Analogue and Digital television what are they? You are using an out of date browser.
It may not display this or other websites correctly. You should upgrade or use an alternative browser. Please help! Thread starter aaqib Start date Nov 28, Chances are it's just the screen size. Yep - it is the screen size, one being a 32 and the other a 36" CRT.
I picked up a 32PD30 myself last year and I can safely say I agree about the weight, so I dread to think how much the 36" weighs!
The guy I bought it from was able to give me a hand at his end but when I got home I realised that the usual suspects I'd call for help were all busy, so it had to spend the night in my car until someone could help me the next evening! I can't help feeling that analogue channels would have looked a lot better on it, but that's progress, eh? Last edited: Nov 29, My is connected but i need to figure out which av ports i should use while connecting my super nintendo or megadrive or even ps2 for the best results!
Click to expand I have tried to connect the tv to the stereo but i am not having much luck with that? If i press 'set up' it comes up with a screen With Q-link 'Av2 out' Which i currently have set to tv whats the deal with these i dont understand them?
0コメント