To remove the projector plate assembly from the boom Put the system in Standby mode by pressing the power button twice on the extended control panel ECP or remote. Wait for the system to enter Standby mode. The power button light on the ECP turns solid amber when the system is in Standby. Disconnect the power cord and all connected cables. Close the projector lens door to prevent scratching or touching of the lens.
While firmly holding the projector with your hand, and without putting pressure or weight on the projector boom, unscrew the thumbscrew that connects the projector plate assembly to the boom. When this thumbscrew is removed, the projector plate assembly swings freely. Put the thumbscrew in a safe place. Lay the projector flat on your work area. Unscrew the three screws connecting the projector plate to the projector.
Put the screws in a safe place. Turn the projector over and lay it on your work area so that the warning lights and setting buttons face upwards To replace the lamp Loosen the two screws on the outer lamp cover with a Phillips No. These screws cannot be removed. Raise the outer lamp cover using a flat screwdriver or your finger. Keep the outer lamp cover in a safe place. Allow sufficient time for the lamp and the inner lamp cover to cool.
They should feel comfortably cool to touch and work with easily. Loosen the screw on the inner lamp cover. Remove the screw and raise the inner lamp cover out of the lamp slot using a flat screwdriver or your finger.
Keep the inner lamp cover and the screw in a safe place. Loosen the three lamp locking screws. Rotate the handle on the old lamp so it faces upwards. Press on the tab and pull up with the handle on the old lamp. Release the tab. Recycle or dispose of the old lamp according to your local waste authority. Remove the new lamp from all of its packaging. Remove the plastic labeling on the lamp handle. Press the tab, put the new lamp into the lamp slot, and push it all the way down.
Tighten the lamp locking screws until the new lamp is secure. Put the inner lamp cover back into its original position. Retrieve the inner lamp cover screw from step 3, and then insert it in its slot. Tighten the screw until the inner lamp cover is secure. Put the outer lamp cover back into its original position. Align the cover and tighten the screws until the outer lamp cover is secure. To replace the projector plate assembly on the projector boom Attach the projector plate to the projector using the three screws that you removed during the projector plate disassembly.
Put the projector plate assembly back on the projector boom by attaching the projector plate hinge channel to the corresponding flange hook on the projector boom.
Note: Hold on to the projector plate assembly firmly when raising the assembly. Retrieve the projector plate thumbscrew that you removed during the removal of the projector plate from the projector boom.
Raise the projector plate assembly while keeping it attached to the flange hook. Pass the threaded rod through the attachment hole on the projector boom, and then secure the projector by attaching and screwing the thumbscrew. Connect the power cord and all the connector cables.
Open the projector lens door. The power button light on the ECP turns green when it starts. You might need to realign the image after you replace the projector plate assembly.
Turn the thumbscrew to adjust the level position while firmly holding the projector. To reset the lamp timer Press the power button on the ECP or remote twice to put the projector back into Standby mode.
The power button light on the ECP turns solid amber when the projector is in Standby. Press and hold the upbutton on the remote control for approximately 10 seconds.
When the projector beeps, press and hold the downbutton on the remote control for approximately 10 seconds. Next Page. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
For the most recent version of this guide, see document on the SMART technical support website. Leave and then ventilate the area where the lamp shattered or burst. Wash your hands thoroughly if you have come into contact with lamp debris. Thoroughly clean the area around the projector, and discard any edible items placed in that area because they might be contaminated. SMART Technologies designed the brackets to support only the weight of the components during normal use.
The following topics describe the features of the components and accessories you received with your retrofit kit. This projector system is easy to install, use, service and upgrade. When the Unifi 45 projector displays an image from a computer onto your touch-sensitive interactive whiteboard, you can draw over the image in digital ink using a pen tray pen or your finger. Use these materials, including the projector and ECP mounting templates, to install your system.
Page Environmental Requirements Environmental Requirements Before installing your Unifi 45 projector retrofit kit, review the following environmental requirements. When the unit is exposed to such a change in temperature, moisture might condense on the lens and crucial internal parts.
If this happens, move the TV or radio away from the projector. Page 17 The image appears taller on the left side when the distance from the projector mirror to the right of the screen is shorter than the distance to the left of the screen.
The image appears taller at the right side of the image when the distance from the projector mirror to the left of the screen is shorter than the distance to the right of the screen.
Page 18 Measure this Lowest Point of distance. However, further adjustments will be required. Boom Front Cover You can now access the adjustment screws. Hex Screw 3 Thumbscrew 1 Thumbscrew NOTE: These images show the mirror from below. Use in combination with thumbscrew 1 shown in the following steps. Page 25 Use the included hex key to adjust hex screw 3 to change the size of the image. Repeat steps 1 through 6, using smaller increments.
Use only one set of the following instructions for your specific installation. You can have up to three peripheral devices and a host computer connected at one time.
The ECP enables you to connect up to three peripheral devices and one host computer at the same time. Page 33 Using Your Remote Control The Unifi 45 projector system remote control enables you to open on-screen projector menus and change the projector settings.
Brightness This option adjusts projector brightness, from to Icon This option turns the icon display On or Off. Selecting Auto automatically starts up the projector when the main power is activated. Default Setting 2 Projection Mode This option enables you to choose from various projection positions.
The default setting is applied at the factory. Do not adjust this option unless advised to do so by a certified SMART technical support representative.
0コメント